Effect of heat treatment and zircon addition on the properties of low-cement castables based on recycled alumina grog

In this investigation, low-cement castables were prepared using 70% alumina grog aggregates obtained from crushed alumina brick waste. The aggregates were thermally treated at 1550 °C for 3 h. Four types of low-cement castables were prepared with various types of aggregates (alumina grog with or without thermal treatment) and fillers (with or without zircon addition), and they were evaluated in terms of their physical, thermal, and chemical properties. Microstructural analysis via scanning electron microscopy (SEM) was performed on the castables before and after slag attack. Compared to the other fabricated castables, the thermally treated alumina grog castables with zircon showed better physical properties, such as a higher bulk density, cold crushing strength, and modulus of rupture and a lower apparent porosity and water absorption. In addition, they had a higher positive linear thermal expansion, refractoriness under load, permanent linear change, and hot modulus of rupture. The results of the SEM with energy dispersive X-ray analysis of the prepared castables confirmed that the mullite and anorthite phases were predominant when zircon was not added and the zircon–mullite phase additionally appeared upon the incorporation of zircon. A quantitative elemental analysis via X-ray fluorescence spectroscopy was employed to determine the composition of the castables. X-ray diffraction analysis showed that the alumina grog castables had a high mullite and low anorthite content, and the thermally treated alumina grog had a high anorthite, low mullite, and high zircon content. The improvement in the mechanical and thermo-mechanical properties of the castables with thermally treated alumina grog and added zircon can be attributed to the formation of the zircon–mullite phase with a low mullite phase content.     

Corrosion behavior of copper in extremely harsh marine atmosphere in Nansha Islands,China

The corrosion behavior of pure copper exposed to the atmosphere of Nansha Islands for 21 months was studied by mass loss method, composition analysis, morphology observation and electrochemical measurements. The results showed that the average corrosion rate of copper exposed for one year was approximately 7.85 μm/a, implying that Nansha Islands was classified as a corrosion category of CX. The structure and properties of the corrosion product layer generated on the front and back sides of the exposed sample differed significantly. The inner corrosion product layer (Cu₂O) on the front side was relatively thick and dense, whereas the outer product layer (Cu₂Cl(OH)₃) was extremely thin. However, the outer product layer on the back side was thicker than the inner layer. Electrochemical measurements indicated that the protection afforded by the corrosion product layer on the front side was improved gradually, while that on the back side was deteriorated.     

Unipolar plasma electrolytic oxidation: Waveform optimisation for corrosion resistance of commercially pure titanium

This study deals with the anodisation of titanium grade 2 in 0.5-M sulphuric acid using a pulsed signal in a unipolar regime. The electrical parameters investigated are voltage, frequency and duty cycle. The use of duty cycles with a high percentage of anodic polarisation (90%), combined with high frequencies (1000 Hz) and the higher voltage tested (220 V), favoured the establishment of a plasma regime involving strong dielectric discharges, allowing the growth of thicker oxides but with rough architecture. The corrosion resistance of the formed film has been characterised by potentiodynamic tests in 0.5-M NaBr for localised corrosion resistance and by immersion tests in 10% v/v sulphuric acid solution for a uniform corrosion assessment. Current–time curves, visual observations and electron microscope analysis (scanning electron microscopy, energy-dispersive X-ray spectroscopy) were the tools selected to provide a correlation between technological parameters and oxide growth mechanism. For localised and uniform corrosion, anodisation at 220 V with a high level of anodic polarisation (90%) and frequency (1000 Hz) was verified to be particularly advantageous.     

Preparation of high-purity SiC ceramics with good plasma corrosion resistance by hot-pressing sintering

High-purity SiC ceramic devices are applied in semiconductor industry owing to their outstanding properties. Nevertheless, it is difficult to densify SiC ceramics without any sintering additive even by HP sintering. In this work, high-purity and dense SiC ceramics were fabricated by HP sintering with very low amounts of sintering aids. Residual B content was only 556 ppm and relative density was more than 99.5%. Furthermore, thermal conductivity of as-prepared SiC ceramics was improved from 155 W m^?1 K^?1 to 167 W m^?1 K^?1 by increasing holding time and their plasma corrosion resistance was promoted in the meantime. The as-prepared high-purity SiC ceramics have broad application prospects in the field of semiconductor industry.     

Evaluation of the localized corrosion on Mg electrode surface by electrochemical noise technique

The symmetrical and asymmetrical electrodes made of Mg were studied in 0.1-M NaCl electrolyte adjusted at pH 12. The statistical and wavelet methods were employed for analyzing the electrochemical current noise (ECN) signals. The asymmetric configuration was used for electrochemical detection of filiform corrosion on Mg electrode. The real time scale of the dominant transients of the asymmetric electrodes was detected on the basis of the maximum peak in the SDPS plots. The SDPS values of the real time scale crystals of the ECN signals resulting from asymmetrical electrodes increased with the increase in immersion time due to the onset of filiform corrosion.     

Carbon corrosion mechanism on nitrogen-doped carbon support — A density functional theory study

In this work, density functional theory (DFT) calculations were used to investigate the mechanism of carbon corrosion on nitrogen-doped carbon support. Free energy diagrams were generated based on three proposed reaction pathways to evaluate corrosion mechanisms. The most energetically preferred mechanism on nitrogen-doped carbon was determined. The results show that the step of water dissociation to form ^#OH was the rate-determining step for gra-G-1N (graphene doped with graphitic N) and pyrr-G-1N (graphene doped with pyrrolic N). As for graphene doped with pyridinic N, the step of C^#OC^#O formation was critical. It was found that the control of nitrogen concentration was necessary for precisely designing optimized carbon materials. Abundance of nitrogen moieties aggravated the carbon corrosion. When the high potential was applied, specific types of graphitic N and pyridinic N were found to be favorable carbon modifications to improve carbon corrosion resistance. Moreover, the solvent effect was also investigated. The results provide theoretical insights and design guidelines to improve corrosion resistance in carbon support through material modification by inhibiting the adsorption of surface oxides (OH, O, and OOH).     

Synergetic effects of photo-oxidation and biodegradation on failure behavior of polyester coating in tropical rain forest atmosphere

This work aimed to study the comprehensive effects of photo-oxidation and biodegradation on different failure stages of polyester coatings,which were exposed to the tropical rainforest atmosphere.The surface morphology,aging products,local aging characteristics and electrochemical behavior of the coatings were characterized with scanning electron microscope(SEM),fourier transform infrared spectroscopy(FTIR),electrochemical impedance spectroscopy(EIS)and high-resolution dispersive Raman microscope.The results showed that the surface of coatings became rougher and fungal hyphae distributed more densely on surface with the increasing of exposure time.From the aspect of polymer structure,the ultraviolet radiation destroyed the main chain of polyester through the photo-oxidation process,resulting in the breakage of aliphatic ester bonds and the formation of esters.Further,the metabolites of fungi can promote the hydrolysis of oligomers produced by the photo-oxidation.In a short,the photo-oxidation could facilitate the biodegradation of the coating.With the synergistic effect of UV photo-oxidation and fungal biodegradation,a rapid diffusion tunnel between the coating surface and the metal substrate was established at the pore defects of the coating,which finally accelerated the corrosion failure process of the coating.The main corrosion products includeα-Fe₂O₃,ZnO and Zn₅(OH)₆(CO₃)₂.     

Electron transfer mediator PCN secreted by aerobic marine Pseudomonas aeruginosa accelerates microbiologically influenced corrosion of TC4 titanium alloy

Titanium alloys possess excellent corrosion resistance in marine environments,thus the possibility of their corrosion caused by marine microorganisms is neglected.In this work,microbiologically influenced corrosion (MIC) of TC4 titanium alloy caused by marine Pseudomonas aeruginosa was investigated through electrochemical and surface characterizations during a 14-day immersion test.Results revealed that the unstable surface caused by P.aeruginosa resulted in exposure of Ti2O3 and severe pitting corrosion with maximum pit depth of 5.7 μm after 14 days of incubation.Phenazine-1-carboxy[ate (PCN),secreted by P.aeruginosa,promoted extracellular electron transfer (EET) and accelerated corrosion.Deletion of the phzH gene,which codes for the enzyme that catalyzes PCN production,from the P.aeruginosa genome,resulted in significantly decreased rates of corrosion.These results demonstrate that TC4 titanium alloy is not immune to marine MIC,and EET contributes to the corrosion of TC4 titanium alloy caused by P.aeruginosa.     

Evaluation of atmospheric galvanic aluminum corrosion in electrical transmission towers at different sites in the Valparaíso region,Chile. Wire-on-Bolt Test (CLIMAT)

This study evaluates environmental aggressiveness and atmospheric galvanic corrosivity categories in Chile (Classification of Industrial and Marine ATmospheres test) by installing bolts in electrical transmission towers in the Valparaiso region across four exposure sites: Playa Ancha, San Sebastián, Las Vegas, and San Felipe. Classifications of marine corrosion index (MCI), industrial corrosion index (ICI), and atmospheric corrosion index (ACI) used different galvanic couples: aluminum/steel for MCI, aluminum/copper for ICI, and aluminum/polyethylene for ACI. Corrosion indices varied by season (summer, autumn, winter, and spring), for which couples were exchanged every 3 months. Intraseason variation depended mainly on the meteorochemical variables of the zone, the Cl⁻/SO₂ ratio, and the presence of general and pitting corrosion in the aluminum. The results indicate that, regardless of environmental condition, the aluminum in Al/steel (MCI) and Al/copper (ICI) couples presented a higher corrosion rate than when not forming a galvanic couple (ACI). Moreover, under higher environmental chloride, these differences increase. The Playa Ancha station presented the highest ACI.